Mylar Bag Sizes for Cannabis: A Gram-to-Dimension Chart (2026)

2026-10-28

Almost every reprint we see starts the same way: the bag was ordered by gram weight, the product went in, and the bag turned out to be either too tall and floppy or too tight to seal over the zipper.

Gram weight is a useful shorthand. It is not a specification. Below is how we convert one into the other, and the four adjustments that change the answer.

Why gram weight alone never determines size

Three variables sit between "3.5 g" and "which bag":

  • Bulk density of the product. Dense trimmed flower, loose trim, and infused gummies at the same weight occupy very different volumes. A 3.5 g figure is a promise about weight, not about displacement.
  • Fill method. Hand-filled bags need more headspace than machine-filled ones, because a person needs room to get fingers in and to work the product down before sealing.
  • What else goes in. A humidity pack, a desiccant sachet, or a small glass jar insert all consume internal volume that the chart below does not account for.

So treat the numbers below as a starting point for a fill trial, not as a purchase order.

Reference chart: typical starting dimensions

Standard flat pouch dimensions by target fill weight. Width × height refers to the outer dimension, before the zipper area.

Target fillTypical outer sizeNotes
1 g2.5" × 3.5" (approx. 65 × 90 mm)Drama bags and single-gram retail. Usually no zipper
3.5 g (eighth)3.5" × 5" (approx. 90 × 130 mm)The most common retail format. Zipper optional
7 g (quarter)4" × 6" (approx. 100 × 150 mm)Add roughly 10 mm in height if a humidity pack goes in
14 g (half)5" × 8" (approx. 130 × 200 mm)Consider a bottom gusset for shelf stand-up
28 g (ounce)6" × 9" (approx. 150 × 230 mm)Stand-up pouch recommended; flat bags slump
Pre-roll (single or multi)2.75" × 6" (approx. 70 × 150 mm)Long and narrow; do not size by gram weight

These are the formats that come up most often in quotes. They are conventions, not rules — a 3.5 g bag at 90 × 130 mm is a starting point that we adjust per product.

The four adjustments that change the number

1. Zipper versus no zipper

A zipper consumes about 8–12 mm of usable height at the top of the bag, and the seal must sit above it. If you take a no-zipper bag and add a zipper without increasing height, you lose fill volume rather than gaining convenience.

2. Child-resistant hardware

Child-resistant sliders and press-to-close mechanisms are physically larger than a plain zipper. On small formats — 1 g and 3.5 g — the CR mechanism can occupy a noticeable share of the bag's face. This is the single most common cause of "the bag got smaller".

3. Humidity packs and inserts

Add internal volume for the insert plus a few millimetres of clearance so it does not sit against the seal bar. Sizing the bag to exactly product plus insert leaves no room to seal cleanly.

4. Label and print area

Compliance labelling is not optional, and it needs flat, unobstructed film. If the artwork needs a warning block, a batch area, and a QR code, check the layout against the finished bag — not against the dieline alone. A bag can be the right volume and still be too small to print on.

Film thickness: the trade-off most buyers miss

Thickness is specified in mil (thousandths of an inch) or in microns. Common choices are 3.5 mil, 5 mil, and 7 mil.

  • Thicker film does not make the bag bigger. It makes the bag stiffer. Stiffer film holds a rectangular shape and resists bulging, which can make a bag feel fuller at the same volume.
  • Thicker film reduces usable internal volume slightly, because the seams and gussets take up more space. On small formats this is measurable.
  • Barrier properties come from the structure, not the thickness alone. A metallised layer or a foil layer does the work; adding thickness to a plain structure mostly adds stiffness and opacity.

If the goal is smell containment for retail, opacity and a proper seal matter more than mil count. If the goal is a premium hand feel, mil count matters more.

How to run your own fill trial

  1. Get three sizes, not one. Order the chart size plus one size up and one size down. The cost of a small trial is far below the cost of a wrong reprint.
  2. Fill with production product, not with rice or scrap. Density is the whole variable.
  3. Include everything that ships — humidity pack, insert, label — before judging the fit.
  4. Seal it and leave it 24 hours. Some structures relax and the fill settles; a bag that looks right immediately can look slack the next day.
  5. Check the seal area, not just the volume. Product in the seal zone is the most common cause of leakers, and it happens when the bag is oversized, not undersized.

The finish changes the perceived size too

A matte finish absorbs light and flattens the surface; a gloss finish reflects and makes the same bag read as tighter and more defined. On a shelf, the same dimension in matte and gloss do not look like the same product. If the artwork depends on a crisp edge, test the finish on the actual film before approving the print run.

What to send us for an accurate quote

To quote properly we need: target fill weight, product type or bulk density, whether a zipper or child-resistant mechanism is required, whether inserts ship inside, the print colours and finish, and the order quantity. With those five, we can propose two or three size options rather than one guess.

Send them to info@mepacks.com or WhatsApp +86 131 4300 7193 and we will come back with a size recommendation and a price for each option.

REQUEST A FREE QUOTE TODAY!

Complete the form below:

Thank you!
Your submission has been received!
Oops! Something went wrong while submitting the form.

REQUEST A FREE QUOTE TODAY!

Complete the form below:

Thank you!
Your submission has been received!
Oops! Something went wrong while submitting the form.
© Copyright © Mecozi Technology Co., Ltd. All rights reserved.